Author Topic: 2015 Versys 1000 #13 and #62 after valve clearance check  (Read 1424 times)

0 Members and 1 Guest are viewing this topic.

Offline CowboyJim

  • Versys Newbie
  • *
  • Posts: 7
  • Bike: Versys 1000, XR560L
  • City / Town: Charlotte
  • Country: us
I just finished checking the valve clearance on my 2015 Versys 1000.  I assembled the bike, except for the air box on.  When I tried to start the bike, the LCD started flashing and it would not start. I found two diagnostic codes: #13 and #62.  I realized that the #13 was most likely because I didnít plug the air temperature sensor in.  Once I did plug it in, I expected the code to clear but it sadly didnít. I would think that would have taken care of the #13. I measured the resistance (ohms) on the air temperature sensor and everything was within spec.

I discovered that I had the plugged the throttle pressure sensors (ST and STP) plugs into the wrong mate.  Once I swapped the plugs (matching the colors), I again would have expected the #62 code to clear, but it didnít.  Thinking that maybe there is an unplugged cable, I looked the bike over and see none (besides the blinkers and that shouldnít matter). 

Do any of you mechanics know what I have overlooked?? I am stumped.  :notsure:

Offline stlee29

  • Versys God
  • *****
  • Posts: 1484
  • Good rides.....
  • Bike: V1K Mk3 2019
  • City / Town: Penang
  • Country: my
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #1 on: January 20, 2020, 06:18:32 AM
Try fixing back all the connections and reset the fault codes. See if they comeback on.
This is a bloody great Bike....!

My V1K Blog: https://www.versys1000.com/index.php/topic,12733.0.html

Offline SouthernCruizer

  • Versys Pro
  • ***
  • Posts: 111
  • Is it Beer:30 yet?
  • Bike: 2016 Versys 1000
  • City / Town: Eunice, LA
  • Country: us
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #2 on: January 20, 2020, 02:32:11 PM
I had the same code for the air temp sensor when I forgot to plug it back in. It took a some cycles of riding and stopping. Think it took me 3 days, then it self cleared.
Jayģ
2016 Versys 1000
2016 Versys 650
2004 Suzuki Wee Strom

Offline Floydsz1

  • Versys God
  • *****
  • Posts: 1756
  • Bike: Versys 1000 2019
  • City / Town: Morecambe
  • Country: gb
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #3 on: January 20, 2020, 04:56:40 PM
I presume it will now start, so ride it round for a few days and once it realises all is okay it will reset itself.

Offline CowboyJim

  • Versys Newbie
  • *
  • Posts: 7
  • Bike: Versys 1000, XR560L
  • City / Town: Charlotte
  • Country: us
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #4 on: January 20, 2020, 07:51:16 PM
*Originally Posted by stlee29 [+]
Try fixing back all the connections and reset the fault codes. See if they comeback on.
How do I do this w/o the bike running or the dealer tool?  If it runs, then 3 riding sessions should take care of it. But I can't get it to start. It keeps flashing the display when I attempt to start it

Offline stlee29

  • Versys God
  • *****
  • Posts: 1484
  • Good rides.....
  • Bike: V1K Mk3 2019
  • City / Town: Penang
  • Country: my
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #5 on: January 21, 2020, 12:47:32 AM
https://www.versys1000.com/index.php/topic,17426.msg201584.html#msg201584

Above, if the bike starts.

Do you have a service manual?  From our forum ... https://www.versys1000.com/index.php/topic,20816.0.html... see troubleshooting

Why can't it start?
Is the side stand down?
Does the normal start-up whine come on?
Check the fuses if possible
Does the 2nd Gen have a kill switch?







This is a bloody great Bike....!

My V1K Blog: https://www.versys1000.com/index.php/topic,12733.0.html

Offline CowboyJim

  • Versys Newbie
  • *
  • Posts: 7
  • Bike: Versys 1000, XR560L
  • City / Town: Charlotte
  • Country: us
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #6 on: January 21, 2020, 02:08:32 AM
I do have a service manual and the Haynes manual.

Offline CowboyJim

  • Versys Newbie
  • *
  • Posts: 7
  • Bike: Versys 1000, XR560L
  • City / Town: Charlotte
  • Country: us
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #7 on: January 21, 2020, 03:55:27 AM
I will try measuring continuity from the ECU to the two alerted sensor connectors. I may call the dealer service department and see what they say too.

Online TowerMan

  • Versys Master
  • ****
  • Posts: 911
  • Bike: Mk1 V650 & Mk2 V1k
  • City / Town: Biggar.
  • Country: scotland
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #8 on: January 21, 2020, 08:13:32 AM
They will tell you to do this first to see if the codes clear  :028:

Once the cause has been fixed, the warning can be reset by by doing the following 3 times:

1. Run the engine more than 10 minutes and
2. Keep the idling speed more than 30 seconds and
3. Run the vehicle more than 5 minutes at a speed of 25 km/h (16 mph) or more. Then
4. Turn the ignition switch off.

If the codes persist then you have a problem  :761:
Richard    :001: 

Offline stlee29

  • Versys God
  • *****
  • Posts: 1484
  • Good rides.....
  • Bike: V1K Mk3 2019
  • City / Town: Penang
  • Country: my
Re: 2015 Versys 1000 #13 and #62 after valve clearance check
Reply #9 on: January 21, 2020, 08:24:32 AM
Jim,

Hope your dealer can do a diagnostic to see what's the problem, since you mentioned you can't start the bike.

Healtech has a OBD but doubt be a help immediately now - https://www.ebay.com/itm/Kawasaki-2012-2019-Versys-1000-Healtech-OBD-Professional-Diagnostic-Tool-/303374448136

For the new V1K 3rd gen, Healtech came up with a FI cleaner - https://www.vanguardmotorsport.com/buy/kawasaki-versys-1000-2018-2019-healtech-fi-cleaner-tool-fi-fault-code-removal/#tab-additional_information

Keep us updated on your progress.
This is a bloody great Bike....!

My V1K Blog: https://www.versys1000.com/index.php/topic,12733.0.html